Arcade Projects
Flaking Ms. Pac-man Artwork Part 2
A week ago last Sunday, my vibrant, pink Bally Ms. Pac-man finally made it’s way down to Indianapolis, IN via a visit from my mother in law.
I originally posted on January 13th about the flaking artwork, how it was severely cracked in spots and starting to flake. With a strong wipe of the hand, I could probably brush off pieces of the pink, yellow and blue artwork. What would have caused this, what type of storage conditions?
At the time, I had limited photos to work with. Here is a close up photo I took to illustrate the flaking a little better on some of the pink bands on the facing right side of the Ms. Pac-man cabinet.
I still intend to go down to an antique shop, if and when I ever have time, with some printed photos of the cabinet artwork and see if anyone has any suggestions. The best I know to do right now is try to put on some sealer, carefully clean the bottom of the Ms. Pac-man cabinet as needed and hope for the best. Like the other post said, most of the products out there are preventative to preserve painted artwork.
I guess the worst case scenario is someday I take the sideart completely off, purchase some TBD Ms. Pac-man stencils, and re-do the whole game. (Once I have my mba, I shouldn’t have to worry as much about cost).
How do I preserve and save flaking arcade game artwork? (Ms. Pac-man)
Back in December, I managed to be the first in line to purchase an old Ms. Pac-man, sitting in a barn in Sagatuck MI. The game has great pink sideart, and is in really good condition overall, plus, I got it for a song.
Well, it sounds like the game will be making its way down to Indianapolis the week of the 21st – 27th. My main concern is that the artwork has some flaking. I don’t know how to preserve it and clean the machine. There is a good amount of dirt ground into the cabinet, like most old games, but I know that if I wipe the game down I will take some of the artwork with it.
Here is a photo example, the only one I have right now, of an area around the kickplate. I think I read somewhere about putting a clear coat on the stenciled sideart of arcade games to give them a shiny finish, and it also helps preserve the painted artwork.
Can anyone give me any suggestions on how to preserve the artwork on the Ms. Pac-man game, and keep it from flaking and peeling off any further? What cleaner, sealer, or other household product can I use to preserve the arcade artwork?
I did a search on the Klov and Google forums, and most of the flaking is related to glass marquee and bezel artwork, but not how to preserve flaking cabinet artwork. I also did a search on the pinball forums, which seem to have a more rich base of information, and the only tip I found there was “use a sealer”. Just like I thought.
- How do I stop cabinet flaking – Google Collecting Groups
- How do you stop cabinet flaking? – Google Pinball Groups
Has anyone used either of these products to seal their flaking arcade cabinet artwork?
The product on the left is Varathane Diamond Water-Based Polyurethane, and the product on the right is Krylon’s Crystal Clear Glaze.
Looking at the website, the Crystal Clear Glaze is advertised as a hi-shine sealer. I imagine that is dependant on the thickness and the coats, but still, that may not work. Thanks to Leinhit for suggesting this to me as an option, whether it may or may not be appropriate for the cabinet artwork vs. glass artwork pieces. Still, my main concern is how I get the dirt off. I doubt that “dabbing” lightly with a wet sponge is going to get all of the dirt out.
Can anyone help me with ideas? Leave a comment with your ideas.
Here are my posts in the different forums about preservation ideas for flaking, if you are interested;
Removing Masking Tape Residue on Arcade Games
On my long to do list of small arcade maintenance activites, here is a photo of my Pengo.
I think the previous owner of this Sega Pengo also couldn’t figure out how to tone down the sound on the game, so they tapes something over the speaker and left it for quite some time. You can see the thick resilient masking tape residue.
Here is what you will need, pretty simple actually.
I started out with a rag and soaked it with Goo Gone, dabbing it on the residue. But I wasn’t able to apply it as thick as I wanted.
Then I figured out to soak the Scotch Brite pad and then apply it to the underside of the cabinet to start to break down the masking tape remnants.
Then, carefully after a few minutes, I scrubbed carefully in a circular motion (not pressing too hard so I didn’t make tiny scratches in the paint) until most of the residue was gone. Here is the underside of the Pengo cabinet under the marquee after I was finished. It isn’t perfect, but it is a lot better and satisfactory for me.
Installing Mark Spaeth’s Jr. Pac-man Toggle Speed Chip Kit
Took me over a month to finish installing Mark Spaeth’s Jr. Pac-man speed up kit, but I can finally rest easy know that my switch is no longer hanging out of my coin door. There was a couple page thread about the kit on the klov forums, mostly people looking to make their Jr. Pac-man gameplay faster. But, towards the end of the thread, there were some good photos and some advice as people started to get the chip replacements in the mail. (more…)
Pengo Locked Up During Gameplay
I had never had this happen before today, but today it happened twice when I was playing my Pengo arcade game.
The first time, a sno-bee got stuck at the top of the screen between two ice blocks, and just kept bouncing there. I didn’t mind, because that meant I could go around the playing field and match up the diamond blocks for my bonus points. I was able to break one of the ice blocks that Sno-Bee was wedged against, and then I smashed him with another block.
But the second time in less than 10 minutes, I was trying to match up the diamond blocks, so I decided I would guide Pengo up next to the dormant Sno-Bee. Well, some of the game code stick executed, Pengo died when he touched the Sno-Bee, but then, the game just sat there, playing the music. Check it out;
I had to turn the upright machine off and back on again. I hadn’t even seen this error in Pengo that causes it to lock up, or freeze. I know sometimes I can run through some of the ghosts in Ms. Pac-man, and even in Pengo, it seems like I get lucky either touching a Sno-Bee without dying or running through one. But not in this case.
Anyone else have this issue with their Pengo PCB board? Is it just mine? If you have issues, does the Sno-Bee only get stuck at the upper right of the play field? Or is it only one board configuration? Or maybe this is just this revision of the PCB, since I know there are a couple. Voice your thoughts.
Got my Pengo High-Score Saver and Enhancement Pack
Pretty excited to come home last night after a long day and see that my Pengo High-Score Saver and Enhancement Pack from jrok had arrived.
This kit for Sega’s Pengo has a ton of goodies in it, if you are interested in buying one, here is the enhancement pack’s homepage. The main options that I wanted were;
- High Score Save – Even when game is turned off, of course I had to have this:)
- Change Music Type – Popcorn Pengo – I can’t stand the original music, Popcorn is what I have always played in Mame
- Freeplay – So I don’t have to coin up every time and increment that counter
I played Pengo last night in between studying. I had to set those high scores:) The Pengo enhancement pack is so simple,fast, and easy to install, as the instructions say (It’s also really affordable at under $50!);
- Step 1: Remove the CPU from the socket (Z-80 Processor)
- Step 2: With the CPU removed insert the Pengo e-pack board into the socket. Take note of the orientation and location of pin 1!
- Step 3: Insert the Pengo e-pack into the Processor Socket (Kit Fully Installed)
I always get nervous when working with these classic arcade games, mostly for the unknown. In the case of this enhancement install, there wasn’t a lot to double check. Make sure the direction of the board is correct (Just double check the direction of the half moon cutout on the Z-80 processor) and make sure it is pressed and secure and that none of the pins were bent on install. Reattach the harness connection in the right direction, and turn on the game. I watched the Pengo PCB in back just in case something happened and I could cut power as needed.
I wanted to see my Pengo scores come back up after I turned the game off. I was running out the door, so I didn’t have a lot of time. I waited about 30 seconds after my last game, turned the game off, waited 30 seconds, and turned Pengo back on. All I got was a flashing message saying something toe extent “Eprom reading high score tables”. The same message you get after each Pengo score is saved. I said a little prayer that it was new, or overheated, or I just did everything too quick, and hoped when I returned that my Pengo high score kit wasn’t broken already. When I got back, the game played fine, so I don’t know what the problem was, maybe I didn’t wait long enough for the next screen. Whatever.
Tonight I will be looking at the enhancement pack options more, to turn off “Game Select” and turn on Freeplay.
Thanks Jrok for making this Pengo high score saver enhancement kit, it really adds a lot of value to my game.
Great Craigslist deal on a Ms. Pac-man with vibrant pink sideart!
I hear a lot on the klov forums of different collectors who have awesome luck picking up some nice arcade machines off of Craigslist for great deals. The closest I have come to that myself, in this area, is an individual who was giving away a complete Gottleib Q-bert in Anderson, IN two or three months back. The key about Craigslist is, you have to monitor it all the time. It is a time consuming thing, and not something that fits into my daily schedule. If I sit down in front of the laptop, I will bring up my RSS feed reader with all of my saved arcade related searches. But if you aren’t sitting in front of a computer the instant that new arcade deal post hits the web, and are caller number 2, you don’t get the deal.
Well, last week Friday, I got lucky. At lunch I was lucky enough to see this posting on Craigslist for Michigan actually (arcade machines in Indianapolis seem hard to come by at jaw dropping deals);
For sale 3 arcade games for parts. Pac Man, Ms. Pac Man & Centipede. $100.00 each. Call (Number removed) for more information.
I thought I would call, that was an excellent price for those machines. The first thing that popped into my head was that this was an individual who wasn’t sure on the value of the machines. It just so happened, I was the first caller! I asked if they had some photos, and she said they did and she’d try to send them to me by the end of the day. That is usually a bad sign for me, because I was so far away in Indianapolis, if another person offered to come get the coin-op games that day sight un-seen, there was nothing I could do.
But luckily, in 5 minutes I had some files in my email. I say files, because they were a Microsoft specific file format type, and not anything I could view. After a chain of calls and emails, I was able to help the owner get the photos changed to .jpgs and sent to me.
I was blown away, and I told them this on the phone. The Ms. Pac-man had a lustrous pink left in the one side of the sideart I could see. I only had one photo to go from, but I had to assume that the sideart on both sides were close in color. I started to get really excited. But what ensued was quite a struggle.
I was the first caller by about 15 minutes, and then the calls just came streaming in. A collector posted on Klov about the machines and then all of the great arcade collecting community in Michigan on the west side was abuzz. Here I sat, down in Indy, with my hands tied a little bit. I knew I was possibly only interested in the Ms. Pac-man, and not the other machines. Gone are the days for me when I was to mess around with reselling arcade games for between a hundred and two hundred dollars. If I resell an arcade game, I want $300 plus to make it worth my while. The other frustrating aspect was, a lot of these collectors who are local, can make a little more money off reselling these arcade games, and that is what they intended to do. I wanted this Ms. Pac-man for my personal collection, having looked for one of this quality for two years at an affordable price, and I didn’t want it to slip through my hands.
After talking with the seller some, it sounded like they only wanted to sell them as a lot. Understandable. At the time they didn’t know about the forum post, and thought that if they did a piece meal with the games, they would be stuck with one, two, or all of them in the end. Not to mention all of the time dealing with a bunch of different individuals and their schedules.
So, I had first priority, but the second person who called said they would come up, by Saturday, and get the games sight unseen, or that is what I was told. I now had a number of things working against me, availability, location, transportation, and time.
I was honest through the deal, and kept the owner’s best interests in mind, knowing that if this was meant to happen, it would. I won’t go into detail, but we worked out a deal. I think in the end, I communicated really well on this deal except for one minor piece. I got what I wanted, the Ms. Pac-man, so that was all that mattered, but the ex-owner is getting a really great deal from me.
Here are the photos I got tonight, and more to come later. First off, I wanted to post photos of my current machine to show the drastic contrast!
~Update 12/22/07 I got to see the Ms. Pac-man in person for the first time today. The Ms. Pac-man marquee has vibrant color with little scratches only on the black portions covered by the marquee brackets. The marquee was secured by non tamper torx screws, which I found odd. I’ll probably replace those.
The Ms. Pac-man glass bezel has just a tiny bit of flaking on the left side and the biggest surprise was the amount of flaking in the sideart. I can just brush off parts of the sideart with my finger if I wanted. The Ms. Pac game is dirty, so I will need to scrub it down, but I am not sure how to do that without taking off some of the sideart. Preserving the artwork will require some research.
I got to the back door through the marquee, checked the connections, powered Ms. Pac-man up, and surprise! It’s a working game! I got a working Ms. Pac-man with great pink sideart for $100. Thanks Craigslist. Hopefully it keeps working after transport.
I need some tips on cleaning the game. Can anyone give me any without ruining the sideart? I have heard of giving arcade games a clear coat to make the sideart shine and protect it, but I don’t want to put that over the dirt. Can anyone help me?
